Throttle Holders
Throttle Holder compatible with ISE ProtoThrottle
Our Throttle Holder Kit is compatible with the ISE ProtoThrottle. It was designed to fit your ProtoThrottle perfectly.
Original design by Scott Thornton, the Throttle Holders is easy to assemble and attach to your layout fascia. The holder is lightweight and strong. It can be painted to complement your layout colors, and it works with the optional finger strap and lanyard. The Proto Throttle Holder holds the throttle securely for storage and at a comfortable angle for stationary use.
Dimensions: 3.75" Deep X 3.6" Wide X 5.75 Tall
We can also create a custom face plate with your Throttle Holder with your Railroad Name and Logo.
Check out this video by Scott Thornton showing the ProtoThrottle holder in use. We recommend using a hook like Scott does in the video to protect your PT from falls.
This video is also available on YouTube.
Sample of a custom engraved Proto Throttle Holder
ProtoThrottle Holder Kit Parts
Assembly Instructions
Select the button below to expand or collapse the instructions.
Mounting Instructions
- Drill pilot holes for your mounting screws.
- Install #6 pan head mounting screws, leaving about 1/8” of exposed thread for the ProtoThrottle Holder to slip onto.
- Install the ProtoThrottle Holder on the screws.
- Tighten the screws to the level desired. Over-tightening may damage the ProtoThrottle Holder.
Zephyr Mounting Shelf
Throttle Holder Kit
Compatible with Digitrax DT602
A Throttle Holder Compatible with the Digitrax DT602 throttles.
We also have a clamp on version with wings for use on modules and temporary placement.
NOTE: The bottom has been updated to have a bigger hole to accommodate the power cord for charging and the Loconet cord for non-radio units that need to be tethered.
They also work with the older DT400 throttles.
They also work with a UT4R throttles.
Assembly Instructions for the DT602 Throttle Holder
Here are the assembly instructions for DT602 Series Throttle Holder.
Select the button below to expand or collapse the instructions.
Parts List - The Throttle Holder is made from two layers of 1/8 Baltic Birch Plywood glued together to make it really strong. The design has very strong corner joints. There is an inner and outer set of pieces. The inner pieces are assembled without any glue, then the outer piece are glued to the inter pieces giving the Throttle Holder strength. You should dry assemble the entire box to become familiar with how it fits together, then remove the outer piece and glue them in place. NOTE: The bottom has been updated to have a bigger hole to accommodate the power cord for charging and the Loconet cord for non-radio units that need to be tethered. |
|
- Place the two Inner Sides onto
the Inner Back.
- Place the Inner Bottom on the
assembly.
NOTE: The bottom has been updated to have a bigger hole to accommodate the power cord for charging and the Loconet cord for non-radio units that need to be tethered.
- Place the two Inner Fronts
on the assembly.
- Spread glue on the outside
of the sides and place the two Outer Sides on the Assembly.
- Spread glue on the front and
bottom and place the two Outer Fronts and the Outer Bottom on the
assembly.
NOTE: The bottom has been updated to have a bigger hole to accommodate the power cord for charging and the Loconet cord for non-radio units that need to be tethered.
- Spread glue on the back and
place the Outer Back on the assembly.
- Clamp as necessary to ensure the parts are all held tightly together. Be careful not to apply too much pressure and bend the sides in.
Parts List - The Throttle Holder is made from two layers of 1/8 Baltic Birch Plywood glued together to make it really strong. The design has very strong corner joints. There is an inner and outer set of pieces. The inner pieces are assembled without any glue, then the outer piece are glued to the inter pieces giving the Throttle Holder strength. You should dry assemble the entire box to become familiar with how it fits together, then remove the outer piece and glue them in place. NOTE: The bottom has been updated to have a bigger hole to accommodate the power cord for charging and the Loconet cord for non-radio units that need to be tethered. |
|
- Place the two Inner Sides onto
the Inner Back.
- Place the Inner Bottom on the
assembly.
NOTE: The bottom has been updated to have a bigger hole to accommodate the power cord for charging and the Loconet cord for non-radio units that need to be tethered.
- Place the two Inner Fronts
on the assembly.
- Spread glue on the outside
of the sides and place the two Outer Sides on the Assembly.
- Spread glue on the front and
bottom and place the two Outer Fronts and the Outer Bottom on the
assembly.
NOTE: The bottom has been updated to have a bigger hole to accommodate the power cord for charging and the Loconet cord for non-radio units that need to be tethered.
- Spread glue on the back and
place the Outer Back on the assembly.
- Clamp as necessary to ensure the parts are all held tightly together. Be careful not to apply too much pressure and bend the sides in.
Ordering
To place an order send an email to orders@prawndesigns.com . Include a list of what you want to order (Part Number and Description) and your shipping address. We will get back to you with an estimate of when we will have your order is ready to ship and shipping costs.
Some items are available in the Prawn Designs Etsy Store.
Please read the Laser Cutting and Engraving FAQ page for details on laser cutting and engraving side effects.
| Part Number | Title and Description | Price | Image |
|---|---|---|---|
Throttle Holder |
|||
PD-21058 |
Throttle Holder Kit compatible with ISE Proto Throttle KitThrottle Holder Kit, compatible with the ISE ProtoThrottle. It was designed to fit your ProtoThrottle perfectly. |
$15.00 |
 |
PD-21060 |
Throttle Holder Engraving KitHave your ISE Proto Throttle Face Plate custom Engraved with your Logo and Railroad Name. |
$20.00 |
 |
PD-21059 |
Throttle Holder Kit compatible with ISE Proto Throttle (Pair) KitA pair of Throttle Holder Kits, compatible with the ISE ProtoThrottle. It was designed to fit your ProtoThrottle perfectly. |
$28.00 |
|
PD-21061 |
Throttle Holder Engraving (Pair) Kit |
$36.00 |
|
PD-21075 |
Zephyr Mounting Shelf KitIf you have a Digitrax Zephyr DCS-51 and want to mount it on the fascia of your layout, this is the shelf for you. |
$20.00 |
  |
PD-21095 |
Throttle Holder Digitrax DT602D KitA throttle holder that is compatible with a Digitrax DT600 series throttle. |
$15.00 |
 |
PD-21097 |
Throttle Holder with Wings Digitrax DT602D KITA throttle holder that is compatible with a Digitrax DT600 series throttle with wing so it can be clamped onto the side of module or placed temporarily. |
$18.00 |
 |
Ordering
To place an order send an email to orders@prawndesigns.com . Include a list of what you want to order (Part Number and Description) and your shipping address. We will get back to you with an estimate of when we will have your order is ready to ship and shipping costs.
Some items are available in the Prawn Designs Etsy Store.
Please read the Laser Cutting and Engraving FAQ page for details on laser cutting and engraving side effects.